广东11选5

自动双组份打胶机的基本工作流程

发布时间:2017/12/04    发布人:

  一、打胶机的特点来介绍双组份打胶机

  First, the characteristics of the glue machine to introduce the double component glue machine

  1、用高压空气在设定的时间内,使用脚踏开关或自动把液体推出。

广东11选5  1. Use the high pressure air in the set time, use the foot switch or automatically release the liquid.

  2、点胶机控制器有点滴,连动,定时滴胶功能;点滴就是直接触发脚踏开关滴胶,并且可通过时间控制点胶量精确度;连动就是用脚踏板之关闭时间多久来控制滴胶时间;定时滴胶就是触发开关通过时间控制滴胶

  2, dispensing controller with drip, linkage, timing function is directly trigger glue; drop foot switch glue, and through the dispensing time control accuracy; is used to control the closing time how long time the glue pedal linkage; timing trigger switch control is epoxy glue through time

  3、自动双组份打胶机采用高精度数码定时控制器,精准控制每次滴定时间,精确到毫秒,正确地控制液料流量,绝不会浪费液料。

  3, the automatic dual component glue machine adopts high precision digital timing controller, precisely control every titration time, accurate to milliseconds, control liquid flow rate correctly, and will never waste liquid material。

  4、只要调节好气压,出胶时间和选择适当的针咀,便轻易改变每次注滴量和注滴时间。

双组份打胶机

  4, as long as the pressure is adjusted, the time of glue is out and the proper needle Tsui is chosen, the amount of drip and the time of drip are easily changed.

广东11选5  5、调整自动点胶阀尾部调节螺丝和胶水的压力可控制出胶量大小。胶量调节螺丝顺时钟向下转动为减小胶量,逆时钟方向转动为 加大胶量。

  5, adjusting the pressure of the rear adjusting screw and glue of the automatic dispensing valve can control the size of the glue. The glue quantity adjusting screw rotates down the clock to reduce the amount of glue, and turns against the clock direction to increase the amount of glue.

  二、双组份打胶机的基本工作流程如下:

  Two. The basic working process of the double component glue machine is as follows:

  (1)首先在打胶机的控制面板设定个好打胶机的打胶速度(默认也可以)

  (1) first in the control panel of the glue machine set the glue speed of a good glue machine (by default)

  (2)将玻璃放入打胶机的工作区域

  (2) put the glass into the working area of the gluing machine

  (3)当设备检测到玻璃后吸盘会自动吸住玻璃以免玻璃在打胶过程中晃动或人为晃动正在进行打胶的玻璃

广东11选5  (3) when the device detects the glass sucker automatically so as not to suck the glass glass glue in the process of shaking in the shaking is glue or man-made glass

  (4)当洗盘对玻璃固定好后,打胶机的机头就开始对玻璃进行打胶动作(不需要进行对玻璃的厚度以及宽度进行设置,打胶机会自动调整并工作)

  (4) when fixed on the glass pad, head of glue machine began to glass glue (without the need for action on the glass thickness and width setting, glue the opportunity to automatically adjust and work)

  (5)以上的步骤重复3次将玻璃的4边全部完成打胶后整个玻璃的打胶工作就算完成了。

  (5) the above steps are repeated 3 times when all the 4 sides of the glass are finished and the whole glass is finished.

  一般在默认的打胶速度每分钟至少可以完成一款2米5见方的玻璃打胶工作,如果将打胶机的打胶速度加快生产会进一步提高。

广东11选5  Generally speaking, at the default glue speed, we can finish at least 2 meters, 5 square glass glue work per minute, if we speed up the glue speed of the glue machine, we will further improve the production efficiency。

  本文由双组份打胶机为您提供,我们的网站是:http://www.tbplay265.com我们将以全心全意的热情为您提供更优质的服务,欢迎您的访问!

广东11选5  This article is provided by two component glue machine。 Our website is: http://www。jncsjx。com, we will provide you with better service with wholehearted enthusiasm, welcome your visit。

广东11选5开奖结果 广东11选5 麒麟棋牌 广东11选5走势图 广东11选5走势图 立即博 广东11选5走势图 广东11选5走势图 广东11选5走势图 广东11选5开奖结果