广东11选5

丁基胶涂布机温控表温度的调整技巧

发布时间:2018/01/22    发布人:

  丁基胶涂布机是完成中空玻璃首道密封的必备设备之一,所起到的作用无可替代,所以也是中空玻璃制作厂家必备设备之一,那么我们就谈一下它的保养与维修,
  Butyl rubber coating machine is one of the necessary equipment to complete the first hollow glass sealing, the irreplaceable role played, so it is one of the necessary equipment of insulating glass production factory, then we will talk about the maintenance and repair,
  出胶比不均匀,调节胶头上的顶丝,二是胶缸不进不退,气动的考虑是气动阀卡了(要常加油)液压的就是液压站油泵漏气,或者是油缸内泄漏(压力升一点马上降下来)三是胶头出胶很不匀,一边粘的很好,另一边不粘,就是一侧加热棒坏了,或者线头断了。
  A binder ratio is not uniform, regulating screw plastic head, two is a rubber cylinder irreversible, pneumatic pneumatic valve is considered card (often to refuel) is the hydraulic station hydraulic oil pump leak, or cylinder leakage (pressure rise a little down immediately) three is plastic head the glue is not uniform, while the viscosity is very good, the other side is the side of the heating rod is not sticky, broken, or broken head.
  检查胶缸、胶头的温度是否正常,压力是否在我们设定的范围之内,检查两胶头的距离是否过大(此距离设定至铝条刚刚能从两个打胶头之间过去为好)。

双组份打胶机
  Check whether the temperature of the rubber cylinder and rubber head is normal, whether the pressure is within our range, and check whether the distance between the two rubber heads is too large (the distance is set to the aluminum strip just to pass from the two rubber heads to the best).
  该设备的胶头加热和胶缸加热,由加热棒两个和加热盘一个提供,由温控表来设定和调整温度的高低,若发现温度升不高或升高后往下降,请检查加热棒或加热盘是否损坏,并检查温控表是否正常。
  The device of glue and glue cylinder head heating heating, a heating rod two and a heating plate, a temperature control table to set and adjust the temperature, if the temperature rise is not high or increased after going down, please check the heating rod or the heating disc is damaged, and check whether the normal temperature table.
  该设备全部采用液压系统,油缸及液压系统全部采用高压油管连接,每个连接处都由组合垫密封,若发现漏油,及时更换组合垫。
  The device adopts hydraulic system, oil cylinder and hydraulic system are all connected by high pressure oil pipe. Each connection is sealed by combination gasket. If we find oil leakage, replace the combination cushion in time.
  皮带跑偏,调节平衡螺杆。六是胶头朵堵了,卸下来,用汽油 洗干净清理脏东西,再安上,以后加胶注意不要沾上脏东西。中空玻璃设备
  The belt runs off and regulates the balance screw. Six is glue head plugging, unloaded, clean clean dirty things with gasoline, and then go up, add glue and pay attention not to dirty things later. Hollow glass equipment
  本文由双组份打胶机友情奉献.更多有关的知识请点击:广东11选5http://www.tbplay265.com我们将用先进的技术.真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.
  This article is a friendship contribution from two component glue making machine. Please click on more related knowledge: http://www.tbplay265.com, we will use the most advanced technology and the most sincere attitude to provide you with the most comprehensive service. We will dedicate more related knowledge to you. Please look forward to it.

广东11选5开奖结果 广东11选5 广东11选5 大圣棋牌 广东11选5走势图 广东11选5开奖结果 立即博 广东11选5 大圣棋牌 大圣棋牌APP下载