广东11选5

双组份打胶机为您讲解中空玻璃的充气过程!

发布时间:2019/07/15    发布人:

中空玻璃的生产过程中特别重要的就是密封环节了,除此之外还有一个同样重要而且在操作系数上来说也是更加困难。中空玻璃的卖点就在于隔音隔热、保温等一系列优良性能,这些性能靠的基本就是中间的充气、之后的密封,这两步骤决定了中空玻璃质量、性能的好坏。今天小编就给大家说说关于中空玻璃的生产条件与组装要求。
In the production process of hollow glass, the sealing link is particularly important. In addition, there is an equally important and more difficult operation factor. The selling point of hollow glass lies in a series of excellent performances, such as sound insulation, heat insulation and so on. These performances depend on the gas filling in the middle and sealing afterwards. These two steps determine the quality and performance of hollow glass. Today, Xiaobian will tell you about the production conditions and assembly requirements of hollow glass.
中空玻璃的原理与充气生产过程控制:
Principle of hollow glass and control of aeration process:
中空玻璃中间夹层是要充进惰性气体,惰性气体不容易与外界发生反应,所以这才能让中空玻璃具备隔音、隔热等优良性能。在中空玻璃中的惰性气体多用氩气,但是氩气是一种无色无味的气体,且其充气浓度不易测量。那如何测量,充气中空玻璃呢。
Interlayer of hollow glass is filled with inert gas, which is not easy to react with the outside world, so it can make hollow glass have sound insulation, heat insulation and other excellent properties. Argon is often used as inert gas in hollow glass, but argon is a colorless odorless gas, and its aeration concentration is difficult to measure. So how to measure it? Inflatable hollow glass.
充气中空玻璃的生产过程控制概念是,为确保充气中空玻璃生产过程处于受控状态,对影响充气浓度质量的生产过程所采取的作业技术和生产过程的分析、诊断和实时监控。它的作用在于对生产过程的质量控制进行系统安排,对直接或间接影响过程质量的因素进行重点控制并制定实施控制计划,确保过程质量。
The concept of production process control of pneumatic hollow glass is to ensure that the production process of pneumatic hollow glass is in a controlled state, and to analyze, diagnose and real-time monitor the operation technology and production process that affect the quality of pneumatic concentration. Its function is to arrange the quality control of production process systematically, to control the factors that directly or indirectly affect the quality of production process, and to formulate and implement control plans to ensure the quality of production process.

双组分打胶机
中空玻璃充气生产过程中需要注意的事项:
Attentions should be paid in the production of air-filled hollow glass:
充气中空玻璃中的氩气需要大约6~8小时才能完全扩散,因此,对中空玻璃氩气初始浓度的检测需在气体完全扩散后才能进行。因此,无论是对充气中空玻璃浓度的在线检测抑或是在惰性气体完全扩散的6~8小时后再检测
It takes about 6 to 8 hours for argon to diffuse completely in air-filled hollow glass. Therefore, the initial concentration of argon in air-filled hollow glass can only be detected after the gas diffuses completely. Therefore, either on-line measurement of the concentration of the aerated hollow glass or after 6-8 hours of complete diffusion of the inert gas
造成充气中空玻璃初始浓度低的主要原因在于充气过程中出现的紊流现象。对充气中空玻璃生产控制的意义在于对整个充气过程进行实时监控,从而有效地避免中空玻璃充气过程中可能出现的紊流现象,提高和保证充气质量的稳定性。
The main reason for the low initial concentration of aerated hollow glass is the turbulence phenomenon in the process of aeration. The significance of production control of aerated hollow glass lies in real-time monitoring of the whole aeration process, so as to effectively avoid turbulent phenomena that may occur during the aeration process of the hollow glass, and to improve and ensure the stability of the aeration quality.
中空玻璃的组装要求:
Assembly requirements for hollow glass:
对环境的要求:温度也应在10-30度之间;2、相对湿度的要求:此种中空玻璃对相对湿度的要求稍低一些,正常情况即可。但应注意的是,干燥剂应选择正规厂家的合格产品,以保证干燥剂的有效使用。干燥剂开封后很好于二十四小时之内用完,因为聚硫胶的透气性较大,密封性差,因此要采用双道密封。用丁基胶作为一道密封,起到阴隔气体的作用。用聚硫胶作为第二道密封,主要作用是粘结作用,其次才是隔气作用。实践证明,单产密封的中空玻璃寿命只有5年左右,而双道密封的中空玻璃寿命可长达20年甚至40年以上
Environmental requirements: temperature should also be between 10 - 30 degrees; 2. Relative humidity requirements: this kind of hollow glass relative humidity requirements are slightly lower, normal conditions can be. However, it should be noted that driers should select qualified products from regular manufacturers to ensure the effective use of driers. The desiccant is better to be used up within 24 hours after opening, because polysulfide rubber has a large air permeability and poor sealing, so double-channel sealing should be adopted. Butyl rubber is used as a seal to isolate gas. Using polysulfide glue as the second seal, the main function is bonding, followed by gas insulation. Practice has proved that the service life of single-product sealed hollow glass is only about 5 years, while that of double-channel sealed hollow glass can be as long as 20 years or even more.
本文由双组份打胶机的小编进行整理编写,如果大家想要了解更多的产品及更详细的精彩内容,请关注我们的官方网站:http://www.tbplay265.com,您的惠顾是对我们很大的支持。
This article is compiled by a small edition of two-component glue machine. If you want to know more about the products and more detailed wonderful content, please pay attention to our official website: http://www.tbplay265.com. Your patronage is a great support for us.

大圣棋牌 广东11选5走势图 广东11选5 广东11选5走势图 广东11选5走势图 广东11选5 广东11选5 立即博 广东11选5开奖记录 广东11选5走势图