广东11选5

打胶机胶嘴两侧余胶的清理方式

发布时间:2017/09/14    发布人:

  一、操作注意事项

  I。 operation notes

广东11选5  1、机头电机下面不要有异物,远离电机以免发生危险。

  1, head motor, no foreign body, away from the motor, so as to avoid danger。

  2、混胶或冲枪(冲洗混胶器、胶嘴)时,必须把机头行走到轨道末端,用接胶板接住胶嘴内放出的胶,以免污染设备。

  2, mix glue or blunt gun (rinse glue mixer, glue mouth) when, must move head to track end, use glue board to catch the glue that releases inside glue mouth, lest pollute equipment。

  3。机头前方检测玻璃开关的光眼上不能有胶,否则误工作。

  3。 front of the nose to detect glass switch, light eye can not have glue, or else work by mistake。

  4、操作参数设置时,在控制箱pc显示屏上进行,根据须要而选择设定值,不要随意设定,以免控制器发出错误的信息,影响打胶质量或损坏设备。

  4, the operation parameters are set on the control box PC display screen, according to the need to select the set value, do not arbitrarily set, so as to avoid the controller to send wrong information, affect the quality of glue or damage equipment.

  5、混胶或冲枪时,一定要先打开胶嘴控制阀门,然后再打开供胶机,以免压力剧增损坏设备或者出现安全事故。

双组份打胶机价格

广东11选5  5, mixing glue or gun, must first open plastic mouth control valve, and then open the glue machine, so as to avoid pressure surge, damage to equipment or safety incidents。

  6、吸盘上不能放石灰粉,如有胶请清理,如果有的玻璃边缘正好放到吸盘的中心时,可调节吸盘左右移动.

  6, the suction cup can not put lime powder, if there is glue, please clean up, if some glass edge just put into the center of the sucker, can adjust the suction cup move around

  7、打胶时一定要扶好玻璃,避免玻璃脱离定位,影响打胶质量。

广东11选5  7, glue, we must help good glass, to prevent glass from positioning, affecting the quality of glue.

  8、冲枪时先关闭机头上的B胶出胶阀门,关闭B胶泵,然后打开B胶回流阀门,后冲枪,冲洗至出胶口不出黑胶,冲洗才能结束。

  8, when the gun, first off the nose on the B glue out valve, turn off the B glue pump, and then open the B glue reflux valve, and finally blunt gun, rinse to the glue mouth, no black glue, rinse to finish.

  9、打三玻时要将铝框检测探针缷掉,双玻时在安装上。

  9, three glass to the aluminum frame detection probe off off, when the installation of double glass.

  10、胶嘴和两侧的刮胶板如胶多时要清理。

  10, rubber and both sides of the scraping board, such as glue for a long time to clean up。

  二、维护与保养

  Two 、 maintenance and maintenance

  1、定期检查电气接线是否有松动及接地可靠性。

  1 、 regularly check whether the electrical wiring is loose and the reliability of the grounding.

  2、新机器经过一段时间的运转之后,应全面检查各紧固件是否有松动现象,并重新紧固。

  2, after a period of operation of the new machine, should be fully checked whether the fasteners are loose, and re tightened。

  3、定期清理混胶器及其前后管道内的凝结胶,定期清理止回阀;发现阻力增高或者堵塞现象,要及时清理。

  3, regular cleaning of rubber mixing device and its front and back pipes of condensation glue, regularly cleaning the check valve; found resistance increased or blocked phenomenon, should promptly clean up.

  4、每次使用完毕,要将机器上的残胶及灰尘清除干净,使机器保持清洁。

广东11选5  4. After each use, remove the residual glue and dust from the machine and keep the machine clean.

  本文由双组份打胶机为您提供,我们的网站是:http://www.tbplay265.com/我们将以全心全意的热情为您提供更优质的服务,欢迎您的访问!

  This article is made up of a two component press machine。 Our website is: http://www。jncsjx。com/, we will provide you with better service with your wholehearted enthusiasm, and welcome your visit!

大圣棋牌官方版下载 广东11选5走势图 麒麟棋牌APP 广东11选5走势图 立即博 立即博 麒麟棋牌游戏中心APP下载 大圣棋牌APP下载 广东11选5走势图 立即博