广东11选5

降低双组份打胶机老化速度的操作

发布时间:2017/10/24    发布人:

  1、双组份打胶机本身质量问题,这种情况我们不是没有遇到过,但是这种情况发生的几率非常的小,但是也非常的容易让人忽略的一个问题,所以小编在这里还是有必要同大家说下这个原因。

  1, the colloid quality problems, this situation we have encountered, but the probability of this happening is very small, a problem but also very easy to ignore, so small in here is necessary for the same people said this reason.

  2、出现中空玻璃打胶机生产出来的中空玻璃密封不好的另一大主要原因就是我们的铝条安装过于随意,尽管我们的设备无需进行设置可全自动的检测并处理深浅不一的铝条,但是如果差距太大且打胶速度过快的话也是有可能发生中空玻璃密封不严漏气的情况。

  2, hollow glass hollow glass glue machine produced not sealed another major reason is that our aluminum installation is too arbitrary, although our equipment without setting aluminum automatic detection and processing depth, but if the gap is too large and too fast then glue it may occur hollow glass Mifengbuyan leak case.

  3、打胶机的供娇压力如果不够的话也是会出现这个问题的,因为打胶机的胶体完全靠气压来挤出设备并完美的涂装在中空玻璃的铝条中的。如果压力过小的话也会导致中空玻璃打胶机密封不严

  3, if the pressure of the glue machine is not enough, it will also appear this problem, because the glue of the glue machine is completely squeezed by the air pressure equipment, and perfectly painted in the aluminum strip of the insulating glass。 If the pressure is too small, it will lead to the sealing of glass sealing machine is not strict

  只要我们做到以下的几点那么我们就能够有效的降低设备的老化速度保证中空玻璃双组份打胶机能够长久稳定的运行。

广东11选5  As long as we do the following points, then we can effectively reduce the aging rate of equipment to ensure that the insulating glass two component glue machine can run stably for a long time.

双组份打胶机哪家好

  一、操作人员好每天都要对打胶机设备的外表上做一番清理。一般要注意要让残留的硅胶和杂物灰尘彻底清理干净,并且要保持工作室内的清理,防止打胶机受到外在环境的干扰。

  First, the operator is best to fight every day on the surface of the rubber machine equipment to do a clean-up。 Pay attention to the residual silica gel and debris, dust thoroughly clean, and to maintain the cleaning room, to prevent the glue machine by external environment interference。

  二、在保证了打胶机的外表干净整齐的前提下,要注意防止打胶机的操作中的污染物料污染到打胶机的局部,尤其不能干扰到打胶机的重要零部件,比如枪头部分等等。

  Two, to ensure the premise of atx-ii looks clean and tidy, should pay attention to prevent the pollution of material pollution atx-ii operation to local glue machine, especially not interfere with important parts of glue machine, such as gun head etc..

  三、为了防止打胶机的轴杆以及密封圈老化或者受损,操作人员好定期使用硅油对其进行清洗。清洗完毕后好能保持其干燥,并保证放置在比较封闭的地方。

  Three, in order to prevent the glue machine shaft and seal aging or damaged, the operator uses the best regular silicone oil to clean it. After cleaning, it is best to keep it dry and make sure it is placed in a relatively closed place.

  四、我们需要对中空玻璃双组份打胶机的供胶部分进行定期的清理,比如胶管、混胶器、胶头等。因为我们加工生产中空玻璃所使用的胶体的特殊性极易有部分胶体残留在这些零部件内容易造成如出胶不均等故障的出现。

  Four. We need to regularly clean the rubber parts of the double glazing machine, such as rubber hose, mixer and glue. Because of the particularity of the colloid used in the production of insulating glass, it is easy to have some residual colloid in these parts, which is easy to cause the uneven breakdown of glue.

  以上便是双组份打胶机今天的分享,您还满意吗,欢迎关注我们的网站:http://www.tbplay265.com并且关注我们的产品,我们将为您提供优良的产品,衷心的愿与您建立合作关系。

  The above is to share the two-component glue machine today, you still satisfied with it, welcome to our website: http://www。jncsjx。com and pay attention to our products, we will provide you with excellent products, sincerely wish to establish business relationship with you。

广东11选5走势图 麒麟棋牌 立即博 立即博 广东11选5开奖记录 广东11选5 广东11选5 大圣棋牌 立即博 广东11选5