广东11选5

操作参数设置不对直接影响打胶的质量

发布时间:2017/12/05    发布人:

  操作注意事项
  1. Precautions for operation
  1、混胶或冲枪(冲洗混胶器、胶嘴)时,必须把机头行走到轨道末端,用接胶板接住胶嘴内放出的胶,以免污染设备。
  1, when mixing glue or punching gun (Flushing glue mixing machine and rubber nozzle), we must walk the machine head to the end of the track, and use the adhesive plate to catch the glue released from the rubber nozzle, so as not to contaminate the equipment.
  2、操作参数设置时,在控制箱pc显示屏上进行,根据须要而选择设定值,不要随意设定,以免控制器发出错误的信息,影响打胶质量或损坏设备。
  2, when the operation parameter is set, it is carried out on the PC display box of the control box. According to the requirement, the setting value is selected, and it is not set at will, so that the controller can send out the wrong information, affect the quality of glue or damage the equipment.
  3、混胶或冲枪时,一定要先打开胶嘴控制阀门,然后再打开供胶机,以免压力剧增损坏设备或者出现安全事故。
  3, when mixing or flushing the gun, we must first open the glue nozzle to control the valve, and then open the machine, so as to avoid the damage to the equipment or the safety accident.
  4、打胶时一定要扶好玻璃,避免玻璃脱离定位,影响打胶质量。
  4, when the glue is played, the glass must be helped to avoid the glass out of the position and influence the quality of the glue.
  5、冲枪时先关闭机头上的B胶出胶阀门,关闭B胶泵,然后打开B胶回流阀门,后冲枪,冲洗至出胶口不出黑胶,冲洗才能结束。
  5, when firing, first close the B glue discharge valve on the machine head, close the B glue pump, then open the B glue reflux valve, and finally flush the gun, rinse to the gel outlet without black glue, and rinse it to finish.
  6.机头电机下面不要有异物,远离电机以免发生危险。

双组份打胶机多少钱
  6. machine head motor under no foreign objects, away from the motor to avoid danger.
  7.机头前方检测玻璃开关的光眼上不能有胶,否则误工作。
  7. a glass switch in front of the head can not have a glue in the light eye, otherwise the work will be mistaken.
  8.胶嘴和两侧的刮胶板如胶多时要清理。
  8. the rubber mouth and both sides of the scraper, such as glue, should be cleaned up.
  9.吸盘上不能放石灰粉,如有胶请清理,如果有的玻璃边缘正好放到吸盘的中心时,可调节吸盘左右移动.
  There is no lime powder on 9. suction cups. If you have glue, please clean it. If some glass edges are just in the center of the suction cup, you can adjust the sucker to move around.
  10.打三玻时要将铝框检测探针缷掉,双玻时在安装上。
  10. hit three glass to the aluminum frame detection probe off off, when the installation of double glass.
  安装探针:将探针上的弹簧压到小时探针的前端与胶嘴平齐时固定好。
  Install the probe: press the spring on the probe to the front end of the hourly probe and fix it when the nozzle is flat.
  二、维护与保养
  Two, maintenance and maintenance
  1、新机器经过一段时间的运转之后,应全面检查各紧固件是否有松动现象,并重新紧固。
  1. After a period of operation, the new machine should be fully checked for loosening of the fasteners and re fastening.
  2、每次使用完毕,要将机器上的残胶及灰尘清除干净,使机器保持清洁。
  2. After each use, it is necessary to clean the machine's residual glue and dust to keep the machine clean.
  3、定期检查电气接线是否有松动及接地可靠性。
  3, check whether the electrical wiring is loose and grounding reliability.
  4、定期清理混胶器及其前后管道内的凝结胶,定期清理止回阀;发现阻力增高或者堵塞现象,要及时清理。
  4. Periodically clean the coagulator and the condensate in the front and back of the pipe, clean up the check valve regularly; find the resistance increase or blocking phenomenon, to clean up in time.
  您的需求就是我们努力的方向,您的追求就是我们的追求,欢迎您的到来,我们一起进步,一起创新!
  Your demand is the direction of our efforts, your pursuit is our pursuit, welcome your arrival, we progress together, together innovation!

广东11选5走势图 立即博 广东11选5开奖结果 广东11选5 广东11选5走势图 广东11选5走势图 广东11选5走势图 广东11选5 立即博 立即博